’72 Chevelle PARTS:

Below is a listing of the new parts purchased in the restoration of my 1972 Chevelle SS:



1.       Full length set of floor panels

2.        Intermediate floor panel

3.        Toe kick panels

4.        LH & RH door skin panels

5.        Used LH donor door-Mike in Connecticut

6.        New shifter hump repair panel-4 speed with console

7.        Energy Suspension polyurethane bushing kit

8.        Hotchkis boxed rear control arm kit w/support braces

9.        New steel brake lines front & rear (complete set)

10.                         New brake hoses front & rear

11.                         New front brake rotors, calipers, pads, hardware kit, bearings

12.                         New rear brake drums, shoes, hardware kit

13.                         New emergency brake cable kit (complete)

14.                         Master Power Brakes 9” dual-diaphragm booster & M.C.

15.                         New ball joints, centerlink, all drag link ends, idler arm

16.                         AC Delco stock rear shocks, Gabriel gas charged front shocks

17.                         Energy Suspension greaseable front sway bar bushings

18.                         GM N.O.S. 7/8” rear sway bar

19.                         Rear sway bar shim kit & mounting bolts

20.                         New rear drive shaft u-joints

21.                         New rear axle pinion seal

22.                         New axle seals

23.                         Chrome differential cover w/bolts

24.                         AGR 12:1 quick-ratio steering box

25.                         Triangle Engineering 20-gallon aluminum fuel cell w/2” sump

26.                         Triangle Engineering –8AN roll-over check valve

27.                         Mallory Comp 110 electric fuel pump

28.                         Aeroquip –8AN fittings, braided stainless steel racing hose

29.                         K&N billet fuel filter w/mounting bracket

30.                         K&N mini-breather for fuel cell venting

31.                         BG fuel pump wiring relay

32.                         Mallory fuel pressure regulator

33.                         MSD 6AL ignition, Blaster 2 coil, MSD mechanical distributor

34.                         MSD HEI style terminal cap & low alkyd rotor

35.                         MSD 8.5MM red plug wires

36.                         Be Cool aluminum radiator w/mounting brackets.  Be Cool Aluminum 1-quart catch can

37.                         SPAL dual electric fans w/relays

38.                         March billet aluminum serpentine belt pulley kit

39.                         Tough Stuff chrome plated 80A alternator-external regulator

40.                         TD Products chrome upper alternator mounting bracket

41.                         Dynomax ceramic coated headers

42.                         Flowmaster GM A-body style 2.5” mandrel bent exhaust system

43.                         Flowmaster 40 series mufflers

44.                         GM SS style exhaust tips

45.                         Demon 850 cfm Vac. Second carburetor

46.                         K&N high flow 4” air filter & lid assembly

47.                         BG fuel pressure gauge

48.                         BG fuel inlet fittings, Aeroquip “T” fittings & inlet line (custom)

49.                         Mr. Gasket 1” phenolic plastic carb spacer

50.                         ARP 2” stainless carburetor mounting stud kit

51.                         Mr. Gasket carburetor return spring kit w/bracket

52.                         ZZ 502 GM crate motor

53.                         Lakewood blow-proof bell housing w/block saver plate-EBAY

54.                         Hays steel flywheel

55.                         Hays diaphragm-style clutch & throw out bearing

56.                         GM clutch release fork

57.                         Lakewood adjustable length clutch fork pivot stud

58.                         OPG supplied clutch z-bar, pivot studs, bushings, parts

59.                         Muncie M-20 4 speed transmission, rebuilt by John Turner, Mass

60.                         Hurst Competition Plus 4 speed shifter for 72 Chevelle w/console

61.                         New speedometer cable for Muncie 4 speed transmission

62.                         Various ARP studs & bolts used extensively on motor

63.                         GM high torque mini-starter

64.                         American Racing Torq-Thrust “D” wheels, 15x8.5 with 3.75" backspacing

65.                         BFG Radial T/A’s:  P275/60R15 Rears, P235/60R15 Fronts

66.                         SS engraved center caps for American Racing Torq-Thrusts

67.                         Acorn lug nut kit w/one lockable nut per wheel

68.                         Restored full-gauge SS dash scored on ebay, summer of 2000

69.                         Grant collectors edition steering wheel

70.                         Restored tilt steering column w/new ignition switch & turn signal

71.                         Optima “yellow top” dual post battery

72.                         Aerospace Engineering Billet battery hold down frame

73.                         Original side post battery cable set

74.                         ARP bell housing stud kit

75.                         CSI billet aluminum distributor hold down clamp & stud

76.                         Edelbrock Victor Series aluminum long-style water pump

77.                         Mr. Gasket chrome o-ring style thermostat housing

78.                         Mr. Gasket hi-flow thermostat

79.                         Dayco upper & lower radiator hoses

80.                         Reman. power steering pump w/reservoir-Wrenchhead.com

81.                         Dayco 6-rib flat style alternator & power steering belts

82.                         New forward engine harness (NPD)

83.                         New intermediate wiring harness (NPD)

84.                         New rear lighting & fuel tank sender wiring harness (NPD)

85.                         New clutch neutral safety switch harness (YR One)

86.                         New console wiring harness (NPD)

87.                         New console top plate & shift pattern label for 4 speed-OPG

88.                         New rubber dust boot & plastic tunnel shroud for shifter-OPG

89.                         New dome light switches in LH & RH door jambs

90.                         Mr. Gasket oil pressure/fuel pump safety switch

91.                         Re-plated original rear bumper from EBAY

92.                         New reproduction front bumper from EBAY

93.                         New bumper mounting bolts-OPG

94.                         Delco-Remy voltage regulator

95.                         New exterior mirror set-NPD

96.                         New lock cylinders for ignition, trunk, doors, glovebox-NPD

97.                         New GM accelerator pedal cable-Ground Up

98.                         High-tech clutch linkage rod set w/teflon heim joints-Speed Direct

99.           JAZ 45-degree, short-style fuel cell filler neck & cap

100.        APC chrome-plated fire extinguisher w/mounting bracket

101.        Auto Meter 2 5/8" Phantom-Series mechanical oil pressure gauge w/mounting panel

102.        Lokar flexible braided steel oil dipstick & handle

103.        Auto Meter -4AN braided steel oil pressure line

104.        Hotchkis front & rear 2" drop spring kit

105.        KYB Gas-Adjust shock absorbers (4)

106.         Edelbrock "no-hop" bars

107.          PPG tinted windshield & rear glass panel

108.        Complete set of weather stripping for doors, windows, trunk

109.        Custom Autosound AM/FM/Cassette stereo with 10 disc CD changer

110.        Kenwood 6"x9" 140-watt rear speakers

111.        Kick panels with 80-watt speakers built in

112.        Dash speaker kit to replace mono unit

113.        Remote trunk release mechanism w/correct push button-ebay